Skip to main content

Morning Overview

A badly made camshaft can crack and cut power in some Toyota Tundras, raising crash risk

A Tundra owner in the 2022 to 2026 model range who has never had a day of trouble could still be driving a truck with a part that may break apart at highway speed. Toyota said in a Nov. 13 release that an engine camshaft in some non-hybrid Tundras may have been manufactured incorrectly and “could snap during driving.”

The recall covers about 62,000 trucks in the United States and, if a camshaft fails, can cut engine power and raise the risk of a crash. Toyota expects to tell owners by mid-January 2027, and the repair costs nothing.

Which Tundras are in the recall

Toyota’s press release lists non-hybrid Tundras from model years 2022, 2023, 2025 and 2026. The company puts the U.S. total at roughly 62,000 vehicles. Local TV coverage, including a Fox 4 Dallas-Fort Worth report on Nov. 18, used the same rounded figure.

The model-year list has a gap. The 2024 Tundra is not in the recall, and the autoevolution report notes that Toyota did not explain why. Hybrid Tundras, sold as the i-Force Max, are also outside the campaign, as the Sequoia SUV is, according to Motor1. The affected engine is the twin-turbocharged 3.4-liter V6.

Canada is part of the same problem. Autoevolution reported another 6,835 trucks there, which brings the combined total to about 68,835.

A single production lot, about 300 camshafts

Only a small share of those trucks should actually carry a bad part. Toyota’s release says all of the suspect camshafts came from one production lot at one supplier, and the company estimates that about 300 of them were installed in vehicles. Autoevolution adds that the suspect cams were fitted to cylinder bank one only. The supplier has not been named in any of the material reviewed.

That arithmetic explains the recall’s design. Toyota is recalling every truck that could hold a part from the lot because it cannot tell from the outside which ones do. A dealer will inspect each truck and replace the camshaft only where it came from the affected lot. Trucks with camshafts from elsewhere need nothing more.

Toyota has not described a root cause. Autoevolution speculated about weak casting, improper heat treatment or shipping damage, but flagged these as guesses and not findings.

A broken camshaft, and the engine recall before it

A camshaft that cracks and breaks inside the engine can cause a sudden loss of motive power, which Motor1 described as most dangerous at highway speed. Toyota’s release says a snapped camshaft could cut engine power at higher speeds, and the company says that raises the risk of a crash. Motor1 quoted Toyota’s description of an “incorrectly manufactured camshaft that can crack and break apart inside the engine,” and reported that Toyota has not tied the defect to any confirmed crash or injury.

Toyota’s notice to dealers and owners frames the fix as inspection first, replacement second, so a truck is not taken apart unless its camshaft traces to the suspect lot.

Camshafts are not the first engine trouble for this generation of Tundra. In 2024, Toyota filed campaign 24V381 after finding that debris from the manufacturing process could contaminate the engine and cause the main bearings to fail, which can stall the engine and cut drive power. The NHTSA record as mirrored by Justia shows about 102,092 vehicles across the 2022 and 2023 Tundra and the Lexus LX 600, with a remedy of replacing the engine assembly. Owner letters for that campaign went out on Dec. 17, 2024, and the filing describes the replacement program as phased, with the Tundra’s fourth phase of remedy parts expected in May 2025.

For a Tundra buyer comparing years, the two campaigns point at different problems: debris left in engines during assembly in one case, and a single bad lot of a purchased part in the other. Toyota has not suggested the two are related, and no source reviewed for this article draws a connection.

Autoevolution reports that campaign was later expanded to cover some 2024 models, in May 2026. The new camshaft recall is separate and has its own paperwork, and the 2024 trucks swept into the earlier action are missing from this one.

What owners can do before the letter arrives

Toyota’s instruction, relayed by Fox 4 in its Nov. 18 report, is that owners bring the truck to a dealer once notified. Motor1 quoted the company’s line that “owners don’t need to do anything yet beyond watching the mail.” Anyone who would rather check now can enter a VIN or license plate at Toyota.com/recall or on NHTSA’s recall lookup, and Toyota’s Brand Engagement Center takes questions at 1-800-331-4331.

The recall’s notification date has been reported inconsistently. A Spokesman-Review item carried a Dec. 28 date for owner letters, while Toyota’s own release and the Motor1 and Fox 4 stories say mid-January 2027. The company’s figure is the one a VIN lookup will confirm.

Open questions remain: Toyota has not said which supplier made the lot, why the 2024 model year escaped, or how many of the roughly 300 camshafts are in trucks still on the road. Those answers will have to come from the formal recall filing that Toyota submits to NHTSA, which should list the production dates for the suspect lot.

This article was produced with the assistance of AI and reviewed by Morning Overview editors prior to publication.


More from Morning Overview


Morning Overview is reader-supported. Some links in our articles are affiliate links, and we may earn a commission at no extra cost to you. As an Amazon Associate I earn from qualifying purchases. Full disclosure.