Skip to main content

Morning Overview

Drivelines may separate on brand-new Kenworth big rigs

A new Kenworth tractor rolls off a dealer lot with a few hundred miles on it, and somewhere under the cab a small steel ring that should hold the driveline together may simply not be there. Paccar, Kenworth’s parent, has recalled 2027-model Kenworth trucks for exactly that: a driveline that may be missing a snap ring and can separate from the truck.

Read next on Morning Overview: Tesla’s Cybercab has already crashed 8 times, and the worst one came at highway speed

The problem was traced to a supplier part rather than to Kenworth’s own assembly, and it reaches well beyond one brand. Daimler Truck North America opened a matching recall for its Freightliner and Western Star trucks the same week.

What is missing from the driveline

According to Commercial Carrier Journal’s account of NHTSA recall 26V-743, the drivelines may be missing a snap ring in the slip yoke assembly, which can let the bearing cup separate from the driveline. The slip yoke is the sliding joint that lets a driveshaft lengthen and shorten as the truck’s suspension moves, and the snap ring is what keeps the bearing cup captured in it.

The risk, per the same account, is loss of drive power. NHTSA documents cited by CCJ also say detached components can become a road hazard for other drivers.

Heavy Duty Trucking, which covered the recalls on Nov. 16, traced the shafts to Cummins: certain Cummins-supplied driveshafts in the RPL10, RPL14, RPL20, RPL25, RPL35 and 176MXL series may lack the ring, and without it, driveline components can shift out of position. Drivers may hear abnormal vibration or noise before a failure, the publication reported.

Five Kenworth models, two different counts

The Kenworth models named in the recall are the T280, T380, T680, T880 and W990, all model-year 2027. ConsumerAffairs listed the campaign, NHTSA recall ID 26V743000, under the plain-language heading “Driveline May Separate” in its recall roundup for the week of Nov. 16, though its listing does not give a unit count.

The trade press does, and the two accounts differ. CCJ put the Kenworth total at 938 trucks. Heavy Duty Trucking reported 982 trucks built in August and September 2026 and an expected defect rate of fewer than 1 percent. The gap is small, but neither outlet’s page explains it, and the NHTSA report itself was not available to confirm which figure is current, so both are attributed here rather than blended. The scale is modest: fewer than a thousand trucks. The expected defect rate of under 1 percent means most of those trucks are expected to have the ring in place, and the inspection exists to find the exceptions.

Inspect, replace, and wait for January letters

The fix is a dealer visit. Kenworth dealers will inspect the driveline and replace it as necessary at no charge, CCJ reported. Heavy Duty Trucking’s account states the check plainly: “The driveline will be inspected to make sure the snap ring is in place.” If the ring is there, the truck keeps its driveline; if it is missing, the driveline comes out.

Owner notification letters are expected to be mailed Jan. 10, 2027, according to CCJ. Kenworth’s own recall number for the campaign is 26PACK, and the publication listed Kenworth customer service at 1-425-828-5888 for questions. Fleets that bought 2027 trucks this fall are the likeliest owners, since the affected trucks were built only in a two-month window.

The Daimler side runs on the same logic with a bigger count. DTNA’s recall, NHTSA 26V-737, covers 3,894 trucks per CCJ, including 2027 Western Star 49X and 47X, Freightliner Cascadia Fifth Gen and Cascadia, 114SD, Business Class M2 and 108SD models. Cummins will do those inspections, and letters are expected Jan. 5, 2027. Heavy Duty Trucking put the Daimler build window at July through October 2026 and the expected defect rate at about 1 percent.

Not the only Paccar recall this month

Work Truck Online’s November 2026 recall roundup lists two more Paccar campaigns that touch Kenworth. Recall 26PACJ covers 26,729 trucks, including Kenworth T370, T270, T280, T480 and T380 models, because remote fuel filter hoses may separate from the fitting and cause a leak and engine stall; owner letters begin Dec. 20, 2026. Recall 26PACH covers 310 trucks, among them Kenworth T680, T880, W900 and W990 models, over sleeper bunk belt webbing that was not secured properly in manufacturing, with letters expected Dec. 13.

Paccar’s driveline campaign arrived in the same weeks as another Kenworth-related filing. In NHTSA recall 26V744, submitted Nov. 11, 2026 as Paccar’s 26PACL, the company recalled 6,185 trucks, among them 2,790 Kenworth T680 tractors, 341 T880 tractors and seven W990 tractors, plus Peterbilt models, over a Bendix forward-looking radar that can brake for objects in the adjacent lane.

That recall is a software matter, with a field update as the remedy, and it is separate from the driveline problem. A 2027 T680 or T880 owner could in principle be named in both campaigns, which makes the VIN lookup on NHTSA’s site the practical way to find out.

What remains unsettled is the final count. If Paccar’s January letters and NHTSA’s database settle on 938, 982 or something else, that figure will be the first firm answer to how many new Kenworths left the plant without the part that holds the driveline in.

This article was produced with the assistance of AI and reviewed by Morning Overview editors prior to publication.


More from Morning Overview

Morning Overview is reader-supported. Some links in our articles are affiliate links, and we may earn a commission at no extra cost to you. As an Amazon Associate I earn from qualifying purchases. Full disclosure.